How To Remove A Vanity Light Fixture
Have you had it with those ugly Hollywood lite fixtures? The ones where the bulbs are lined up in a directly line staring you lot in the confront? Did you lot know that you don't have to live with them? Fifty-fifty if y'all live in an apartment, you lot can switch light fixtures out fairly easily. (Be certain to go on the old fixture and all the parts so y'all can re-install information technology before y'all motion out.)
Low-cal fixtures range in price from $xx to well over $200. Sometimes you tin luck out and find some dainty low-cal fixtures on Craig's List or eBay for less.
I hope you tin benefit from this tutorial. I think you'll concur, it is neither difficult nor challenging changing out a light fixture.
Instructions:
Before kickoff the installation you MUST plough off the power to your fixture.
Required Prophylactic Educational activity:
Plow off the ability to the calorie-free fixture you are working on. I highly recommend turning on the calorie-free you lot will be working on, then shut off the circuit at your excursion breaker and check to encounter that the calorie-free has gone out. Also note that just considering the light fixture ability is turned off, it doesn't necessarily mean that other outlets or lights in the same room are on the aforementioned excursion. Ever check for the presence of power before you lot work on information technology.
Tools:
( I've included affiliate links for your convenience. I earn a pocket-sized pct from a purchase using these links. At that place is no boosted cost to you. You can read more than almost affiliate links here .)
- Light Fixture
- Needle-nosed pliers
- Wire cutters and stripper
- Flat caput screwdriver
- Phillips head screwdriver
- Optional: electrical tape
Unpack your new (or slightly used) light fixture. Read through the directions as some steps may vary from this installation tutorial.
Begin by unscrewing the light bulbs and and then remove the collars around the lite bulb sockets.
Locate whatever other screws that might be property the fixture in identify. This fixture simply popped off.
Untwist the wire nuts holding the wires together.
Once all the wires are disconnected, unscrew the two screws holding the mounting bracket.
Remove the mounting subclass…
…and at present y'all should exist able to remove the light fixture. Express joy at any hidden colors and wallpaper beneath the fixture. (Toile! Ah, not so bad.)
You should be left with merely the junction box and 3 wires protruding from the box. The bare or greenish wire is your ground wire. The white is your neutral wire and the black is your hot wire.
If you were eagle eyed, you might have noticed a small nick in the insulation of the neutral wire. This could cause a short, then I wrapped some electric tape around the nick.
Install the new mounting bracket that came with your fixture (if you bought a used one, you may have to utilize the old mounting bracket from the Hollywood Strip). Attach the screws through the subclass and into the junction box.
The mounting subclass that came with my fixture has a rotating bar that can swing 180 degrees. Position this bar so the fixture will hang level.)
Test fit your fixture and arrange the depth of the mounting screws (the "no caput" screws on the mounting bracket) and the angle of the swinging bracket arm. Once the subclass is level and fits snugly with but a small portion of the headless screws poking through; remove the lite fixture and tighten the spiral in the center of the mounting bracket to secure the rotating bar.
Wrap the ground wire from the junction box around the dark-green or bare spiral on the mounting subclass.
Connect the ground wire from the light fixture to the ground wire from the junction box. Twist them together and secure them with a wire nut.
Twist the black wires from the junction box and the light fixture together.
Twist a wire nut on to secure them.
Repeat the same procedure to connect the white wires.
Gently fold and tuck the wires back into the junction box. Try to position the white wires on the opposite side every bit the black wires.
Identify your light fixture onto the headless screws and secure the fixture by screwing on the small ball caps.
Remove the shade band from the light bulb sockets.
Slip the glass shades onto the socket and and then screw the collar back on to hold the glass light shades.
Repeat for the remaining light sockets.
Many vanity light fixtures are reversible.
I decided to rehang my fixture facing up for less direct light and to avoid bumping into the mirror frame.
What practise you think? Do you like the new look? Do y'all think you will attempt it yourself? I hope and so, information technology was like shooting fish in a barrel!
How To Remove A Vanity Light Fixture,
Source: https://www.prettyhandygirl.com/changing-out-a-light-fixture-bye-bye-hollywood-strip-light/
Posted by: castilloconed1940.blogspot.com
0 Response to "How To Remove A Vanity Light Fixture"
Post a Comment